How To Make A Bench Cushion With Piping

January 11, 2019 Post a Comment

Line up the piping with the edges of the cushion. Next i lined it with fleece cut to the same size and stitched along some of.

How To Sew A Box Cushion (With Piping and a Zipper) in

Turn the cushion right side out.

How to make a bench cushion with piping. Press the seam allowances open and flat. Lay out cushion on fabric. Cushion with 3/4″ panel cut.

Sewing hacks sewing tutorials sewing crafts sewing projects sewing patterns sewing stitches sewing tips techniques couture sewing techniques. With the cord inwards, pin the piping around the edge of the cushion top. How to sew a bench cushion with piping following this easy sewing tutorial.

Where the piping overlaps, trim the cord back so that the ends meet and wrap the trimmed cord with the folded end of the fabric. Pattern top and bottom fabric plates to the foam size plus the thickness. Matching the seams of the side ring with the corners of this main panel, pin the side ring right sides together all around.

You will need a a strip of fabric 5cm wide and the length of the piping cord (it may need joins). Use your zipper foot to straight stitch around the edge of the piping. Pin the top piece matching the corners right sides together and pin.

When you get to the corners, lower the needle and lift the foot to turn the cushion panel making. Then turn your piping at a clean 90 degree angle and continue pinning. Be sure the raw edge of your piping is facing the raw edge of the fabric.

Let's get started with today's box cushion diy tutorial! This gives the cushion cover a nice finished quality. With the sides of the cushion cover facing up, start sewing using a 1/2 inch seam allowance in the center of a long side.

Leave one end of the cushion open for inserting the foam. Curve the corners of the fabric plates. When you reach a corner, snip into the raw edge of the piping all the way (but not through) the rope piping.

There is a project that i put off for years, much to the dismay of my patient husband. To further complicate things the fabric strips need to be cut across. Then i flipped the bottom piece upside down, lined it up in a way i liked and stitched the fabrics wrong sides together with a 1/4″ seam.

Give your bench cushion cover a good pressing. Pin all the sides of the cushions together, right sides facing. Pin the piping on top of the fabric.

Finally, i came up with a shortcut to make it easier, quicker, and less expensive. Measure the foam and cut it to the size of the bench (the final cushion will be slightly smaller than the bench). Pin the piping to the front cushion panel by matching up the raw edges with right sides together.

When you reach a corner, snip into the raw edge of the piping all the way (but not through) the rope piping. To make the cushion we need a continuous length of piping 5cm longer than the perimeter of the cushion pad. Pin the side wall piece to the top piece all the way around, snipping the corners just as you did for the piping.

Be sure the raw edge of your piping is facing the raw edge of the fabric. Place one fabric/ batting / piping panel right side up on your work surface. Repin to the top piece and sew all the way around.

Plus, a link to making your own piping. I followed that tutorial exactly so i’ll just post a photo of my piping. Pull it over an ironing board if possible.

(while i did have fabric left over, there wasn’t enough to make the piping. Line up the piping with the edges of the cushion. Line the raw edge of the piping up with the raw edge of the cushion top and when you get to a corner, snip the bias strip so that it bends around the corner.

When you meet back up with where you began, pin one end to the other where the zipper ends and sew to join up the side wall pieces. Article by pretty handy girl. Pressed the seam open and trimmed it down to a 30 1/2″ width.

Using a ½” seam allowance, stitch all the ends together. I found this wonderful piping tutorial from addicted 2 decorating. The next step was to make the piping.

A 46cmx46cm cushion pad requires a length of piping 189cm long. Introducing “plan b”, my diy bench seat cushion cover tutorial. Take the cushion top and lay it right side up.

Gently unpick the corner seams 1/2 down. Fold your fabric (or whatever soft flat substance you chose for your cushion) in half and cut a 3/4″ perimeter around it. Lay the top panel right side up on top of the cushion.

Baste the decorative piping and the plates together with the “out” sides facing in.

Tutorial custom tufted chair cushions with piping