How To Sharpen A Chainsaw With A Round File

December 06, 2019 Post a Comment

The main types of files are the 4mm, 4.8mm, and the 5.5mm files. 2.have the right tools on hand.

Shina 4/6/8/10/12inch Semicircular needle file Diamond

Using the incorrect sized file will damage your file and of course your chainsaw.

How to sharpen a chainsaw with a round file. As we will see on the graph, the primary file options are 4.0 mm, 4.8 mm, and 5.5 mm. When the tools are ready, engage the brake of the chain. For example, a chisel needs a file that can fit on the square cutting edge.

If there is a protrusion of the top of the depth gauge on the slot, this is the part that you need to file out using a flat file. The round file is installed in the holder and fixed with special clips. The chainsaw has to be clamped in the right way.

Buy the correct sized file. A file guide (for holding the round file at a fixed depth while sharpening) a flat file. The sharpening file must be sized correctly for the chain's pitch.

With the cutters identified, you can grab the round file and proceed to check how you’re going to sharpen. Here, we recommend using a file with a diameter of the same or slightly bigger size than the cutters. You should then use a flat file to sharpen the depth gauge so that it keeps its shape.

To properly sharpen your chain, you’ll need four major tools: Before you begin, you have to clamp the chainsaw securely into a vice. How to sharpen a chainsaw chain with a round file.

It comes in either a round file or flat file depending on the type of cutter you are planning to sharpen. Position the file on a tooth. Place the saw in a vise.

Your round file will be needed to sharpen the side and top plates of the cutting teeth. You’ll need a round file for sharpening your chainsaw. Grab the file and prepare.

Free delivery on your first order shipped by amazon. While clamping, you can use the vise or a tabletop clamp. You’re going to start by placing the depth gauge on the saw.

A grinder cutter needs a round file. A file like this will need to match the cutter diameter on your chainsaw. A round file in the same diameter as the cutter.

And then file away till you can rest assured that the chainsaw is sharpened. If the cutter has a pitch of 5.5mm, you will get a 5.5mm round file. 3.set your file in the notch on the front of the cutter.

A chainsaw blade can be sharpened by hand using an appropriate sized round file. Make sure you sharpen all the cutters just as you would if using a round file instead, then switch to the opposite end and sharpen the cutters. The good news is, with the right tools, you can sharpen your chain without even removing it from the chainsaw.

Proceed to other teeth on that side. Flip the saw around and sharpen the other side. Once you start turning the chain and reach the first cutter, you know it’s finished.

The most common cutter sizes are 5/32, 3/16 and 7/32 inches. Once you can get very familiar with using the rotary tool as a chainsaw sharpener, you can conveniently move. Make sure to have the bit you want to sharpen, sticking out from the file gauge.

To sharpen a dull chainsaw, clamp the bar of the chainsaw to your work station and tighten the chain using the tension adjusting screw to make sure it won't move. There are numerous ways to sharpen chainsaw teeth, but hand sharpening is the quickest and easiest method. If you have a chain with a chipper cutter, you will go for a round file.

You can review the requirements for your saw to see what type of round. Each tooth needs to be filed sharp by incorporating a few different techniques for sharpening. Get it tomorrow, mar 23.

From this conversion table, get the matching rounded file. There are several markings on the plane of the holder that indicate a specific sharpening angle. Different chainsaw will need different sized files to sharpen.

The round file is installed in the holder and fixed with special clips. After filing the gullet (slot under the cutter) of the cutter with a round file, put the depth gauge guide on top of the filed cutter and position its slot on the depth gauge. Then, use a permanent marker to draw a line on the link where you're going to start filing, and get a specialty chainsaw file that's the same diameter as the chainsaw.

Asses where the chainsaw rollers are and make sure to be holding your round file at a 90 degree angle from them. The bar and chainsaw must be stabilized so that sharpening will be a safe journey. More on the cutters later on.

You can find the exact dimensions in your chainsaw’s user manual. When straightening the chain with a file with a holder, the markings on the device are placed parallel to the chainsaw tire, which allows you to accurately maintain the required angle. These files can either flat files or round files depending on the cutter you are sharpening.

You should also need both round and flat files to sharpen your chainsaw chains in order to get the best results. So, buy the round file that matches the diameter with the chainsaw’s teeth. You can find a 5/32, 3/16, or 7/32 file among other options for your convenience.

Now clamp the bar lightly in a. When straightening the chain with a file with a holder, the markings on the device are placed parallel to the chainsaw tire, which allows you to accurately maintain the required angle. There are several markings on the plane of the holder that indicate a specific sharpening angle.

When filing the cutter, use only round files to sharpen the top plate and side plate. Three step to sharpen a chainsaw by hand with a file:1.clamp the bar of the chainsaw to your work surface.

How to sharpen a chainsaw See description for link to file