How To Get A Broken Key Out Of A Lock Without Pliers

January 13, 2020 Post a Comment

If you don’t have needle nose pliers, sometimes a pair of sharp pointed scissors can be used to grab the broken key that is just barely sticking out of the lock. Keep doing this until the hook extractor tool reaches one tooth, and you can drag the broken part of the key free.

How to get a new car key made without the original

Similar to the previous instruction, keep the cylinders at a neutral position.

How to get a broken key out of a lock without pliers. Well, maybe later when you need your key replaced, but first, there are 6 ways to get a broken key out of a lock. Use your pliers/tweezers to grip on the end of the broken key. If you cover the keyhole while you tap the lock, you could prevent it from sliding out.

This is how you get the broken key out of the ignition. After inserting the key extractor tool into the lock, turn it slowly toward the key. Pull out the broken key.

Slowly pull the jigsaw blade out of the lock. Often tackling the key from the front can push the key further into the lock. Your best bet to get the entirety of the broken key out of your lock is to take the lock apart.

Make sure the keyhole is facing down. This will expose the cylinder inside of the lock which has a hole that exposes the broken key. The goal here is to try to catch the blade on one or more teeth of the broken key.

You will need an excellent penetrating fabricant oil for spraying inside the keyhole and thin screwdrivers, which will grasp the broken key inside the door lock and take it out. How do you break a lock without a key? Tag needle nose pliers for key extraction.

Then, insert and rake the blade so it catches the key, then pull the blade out so the key is pulled out with it. That way, you’ve got something like a little angling rod you can use to angle out the key. As long as there’s enough key protruding to grip with pliers…

Using super glue to get the key out? Move the saw blade up and down to try and pry out the key. If there is not enough of the broken key to grab it with the pliers you will need to use one of the other methods to get it to that point.

Grip the key with the pliers and pull it straight out. When the hand jigsaw blade stops sliding, you’ve reached the end of the lock cylinder. If your key is broken off in a lock with a removable cylinder, you might get the broken part out by tapping the lock against a hard surface.

Resist the urge to turn the key with the pliers as you're pulling it out. Look at where your key has broken. Grab the protruding key with tweezers or pliers and pull it out.

Insert so it is between the keyhole and the broken key. If you are using a spiral tool instead of a key hooks tool, follow the same method but turn. On the off chance you have a set on hand for the day when you need to get a broken key out of a lock then you insert the hooked key extractor down the top of the key, snag an upright of the key face, hook onto it and pull the key out in one gentle motion.

Before you attempt to extract the broken key bit, using a lubricant can make the job easier. Shape the end of a thin paperclip so it is straight and curved at the end. Get a good hold on one of the key’s teeth and pull the broken piece out.

Pull the blade and key out until enough of the key emerges that you can grasp it with your pliers. You might break the key off inside the lock. If it broke at the head, you must get a screwdriver to turn the lock back into position to allow the key to slide back out.

Carefully turn the jigsaw blade towards the key and try to catch the blades on a tooth (or several teeth) of the key. Try to grip the broken key and pull it out. Attack the key from the backside of the lock by pushing the key through to the side on which it is broken (it isn’t usually easy to pull the key out from the front).

Rake and pull to remove the broken fragment. Doing this will involve some technical knowledge. Using something thin, you can push the broken key out of the front of the lock.

Twist the extractor tool and pull out; If the pliers or the pin don’t work, try applying some cooking spray. Make sure to wait until the glue has set a little bit before attempting to pull the key out.

Push the saw blade into the lock with the teeth facing your way. You may be able to use tweezers but with caution! Push and pull the rake out of the lock, twisting it and working by feel.

Add a bit of lubricant with the straw attachment and wipe off any excess. Now while pulling the tool back, press the handle toward the end, away from the lock. It might take you a few tries, but the broken key will jump right out of the lock.

Hold the tension wrench twisted in the correct direction and insert the rake into the lock where the teeth of the keys would go. There are various videos online about how to remove a broken key from a lock. Once your jigsaw blade has stopped moving, turn it slowly to one side.

Pull the blade out of the lock. If the lock mechanism has become loose, this should stabilize it enough for you to safely pull the key out. Latch onto the broken key piece with your pliers and pull it out of the ignition lock.

Advantages of Using Locksmith Service for Car Key