How To Fix A Pocket Door That Won't Stay Open

May 12, 2020 Post a Comment

This job can be a hassle, especially if you have painted trim. A few minutes work and your door will be quiet and smooth.

12 Modern Sliding Door Ideas That Make a Amzing Home

With the broom handle, slide the roller carriage out into the door opening.

How to fix a pocket door that won't stay open. Tightly screw the new lock, in. Use a level to ensure that the door frame, and subsequently the track, will be perfectly level once installed. If the door still won't stay open without assistance, remove the screws from the top hinge first.

Close the door to have access to the back. Move them closer to the door until they rub and possibly make some friction so the doors do not move on their own accord. Move the top hinge leaf out (away from the door stop molding) or move the bottom hinge in.

Tap some shims under the door to hold it about 1/4″ off the floor. For a slightly bowed door, take a heavy weight and lay it across the area that is warped. Use a pocket door wrench to turn the hanger a quarter of a turn at a time until the door is parallel with the jamb.

While the stopper is holding up the door, place the screws back in the track using the screwdriver or drill. You might have to wedge a flathead screwdriver between the head of the pin and top of the hinge. If anything is out of place, attach shims to the door frame until you get a level reading.

If this is the case, it will require major reconstructive surgery to. Exterior door is hard to open: Adjust the the hangers so the one at the opening sits slightly lower than the other, should only be 13mm spanner and moving two nuts.

So try this trick first. If you are keeping the original strike plate, make sure the new latch bolt will fit in it properly and that there is no gap between the frame and the plate. You can also use glue to do this.

If the door is too high, adjust the screw to lower it. Putting the pocket door back on the track Pull out a door that’s stuck in the pocket by alternately pulling the top and bottom edges.

If your closet door or mirror wardrobe door is off the track or won’t stay on, we can repair or replace it for smooth easy operation. Basically, you are attempting to repair the tension to a workable level. Then, close the door and check the keys again.

After you’ve raised the door and removed the shims, make sure the door hangs at least 3/16″ off the floor. To readjust the door frame, you have to remove the trim along the latch side to get at the shims. Sometimes, fixing a pocket door problem can be as simple as making a few adjustments with a wrench.

One caution, it could rub some of the paint off of the very edge of the door at the very bottom, probably not enough to even notice. New track and pocket door rollers Tap the screwdriver with the hammer until the pin pops up from the hinge and can be removed by hand.

When the wheels are back on the track, push the door back and place the stopper under the door to hold it up. If the door is scraping against the floor, turn the adjustment screw so that it pulls the door upward. Place that piece of cardboard on the door frame where the hinge will be screwed back into place.

The new lock should work perfectly. Troubleshooting and repairing issues with pocket doors is a simple task most of the time. Remove the door, sand, and seal it with primer or polyurethane on the top and bottom edges.

If you have this clearance and the door still rubs, the door may be warped and/or the entire pocket door assembly may be twisted. A flexible lamp of some sort will work well, so that you can bring it closer to the open watch face, or push it a little away if it’s too bright. Replacing the track can be a big job that may even require some drywall patching.

If your pocket door won’t stay on its track easily, you can do some basic steps to fix this. Lift the door gently and place magazines under it to support the door. For those who take such an activity seriously, it is important to have a watchmaker’s bench and a source of light that casts strong but not harsh light.

Leave the weight on the door for 24 hours or until the warp is gone. Old pins may need to be pried loose in a different manner. When a door tends to swing slowly open by itself if not latched, you do just the opposite:

You can try to tighten the threshold screws or replace the threshold and sweep at the same time. If you are lucky, the problem may be fixed by simply tightening all the screws in the hinges. Also check to see if the door sweep has lowered.

After the door is taken out and leaned against the wall, you will have to locate the pocket door hanger. To stop any banging buy a bit of aluminum angle and use that as a guide and maybe a draught stopper to close the gap. When a door won’t stay open, the casing is probably leaning slightly in the wall frame.

This will widen the gap along the hinge side and narrow the gap along the latch side. Without closing the door, check the keys to make sure they work. Rather than remove and rehang it, try removing one of the hinge pins.

Unscrew the sweep and raise it on the door. For a badly warped door, apply wet towels across the warped area only. A broom handle works well for coaxing the hanger out of the pocket.

Cut a piece of thin cardboard to the size and shape of the hinge side piece. Use a flashlight so that you can see what you are doing. If your exterior door is hard to open, it might be from a loosened threshold piece.

Remove the pin by placing a screwdriver under the middle hinge. Place it on a hard surface and whack it in the middle with a hammer. If you have a gap at the bottom of the door that is causing rubbing towards the top of your door, you can lower the door by adjusting the hanger that is.

How to fix a door that won't stay open. Most of the time it is just some adjusting and lubricating. Now tighten all of the hinge screws, on both the door and the door frame.

Fixing A Locked Shut Patio Door Getting It Open