How To Reset Tire Pressure Sensor Chevy Silverado 2008

November 16, 2021 Post a Comment

Press and release either arrow button until the tire pressure screen is displayed, then press the set/clr button. My light came on two days ago.

20082010 Chevrolet Silverado 3500 DUALLY 8076 Wheel

Tighten the torx screw to 1.3 n.m (11.5 lb in).

How to reset tire pressure sensor chevy silverado 2008. Hold it in intell the info comes on. Before performing a relearn procedure, it is important to make sure the tpms sensors are installed properly, and tires are inflated to placard pressure. Listen for a double horn chirp, indicating entry into the tpm learn mode.

Repeat for the rf/rr/lr sensors Horn will chirp twice, dic displays tire learning active; Using the driver instrument cluster, click the “vehicle information” button and navigate to “relearn tire position”.

Resetting the tire pressure sensor on your 2008 chevy silverado can be somewhat complicated, but will only take about 10 to 12 minutes of your time. Assemble the tire pressure sensor (2) to the valve stem and install the new torx screw (3). Does anyone know how to reset the tire pressure monitoring system on a 2008 silverado?

Low tire pressure light is on all tire pressure is. Place your relearn tool against the sidewall closest to the valve stem (where you fill and test your psi). Lf, rf, rr and lr.

The horn will chirp, after the vehicle has received a signal from each sensor. Alternatively, if your silverado does not have keyless entry, press and release the “info” button on the driver’s information center until “tire learn” appears on the dic display. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

Keep your tire pressure monitoring system operating properly with. Ensure the flat of the valve, lines up with the flats of the snap in the enclosure. This week, we will go over tpms diagnostics for the 2008 chevy silverado.

A horn chirp will confirm that the sensor has been reset Repeat the process for the passenger side front tire, passenger side rear tire, and the driver side rear tire. Push the bottom knob ( to turn the station).

Relearning sensor position turn the ignition to the “on” position, but do not start the silverado. Start from the driver side front tire, remove the valve cap, and then increasing or decreasing the tire’s air pressure until a horn chirp sounds. After the horn chirp has sounded, proceed as in step 4 for the next 3 sensors in the following order:

Repeat the process for the passenger side front tire, passenger side rear tire, and the driver side rear tire. A horn chirp will confirm that the sensor has been reset Chevy silverado (2008) type of tpms system:

Direct tpms, sensors are installed in the wheel; Start from the driver side front tire, remove the valve cap, and then increasing or decreasing the tire’s air pressure until a horn chirp sounds. All tires are at about 38 pounds but the light is remaining on.

Use the tool to activate the left front sensor single horn sounds; Push trip reset again to confirm; Press and hold the “set/reset” button.

Push and hold trip reset stem to begin the sensor matching process; Initiate the tire pressure monitor learn mode by simultaneously pressing and holding the “lock” and “unlock” buttons on the keyless entry remote until you hear a. After the horn chirp has sounded, repeat step.

The first thing you will need to do is go to the tire you want to start with, which is the front driver's side tire. Push the trip odometer reset stem until tire pressure is displayed; Using the dic, press the vehicle information button until the relearn tire positions message displays.

Now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times. In the window it will show all the things you can reset. Turn on the ignition, with the engine off.

Starting with the lf tire, use a properly formatted tpms scan tool to scan each sensor in the foll owing order: Turn off the radio and turn the key to the on postion. Check if this fits your 2008 chevrolet silverado 1500.

Click “set/reset” and a message saying “tire learning active” will pop up. All you should need to do is check and set all tire pressures and make sure to check the spare also, after all tires are set with air you then drive a few blocks and the light should reset if the light does not reset then you will need to find out which wheel has a bad air pressure sensor, this is done with a tool that is put on the valve stem or a scan tool to see which tire is showing the wrong pressure,. I checked tire pressure and added a little air to each.

Set 4 TPMS Tire Air Pressure Sensors 315Mhz Metal fit 2014