How To Fix A Pocket Door That Won't Stay Open

May 05, 2022 Post a Comment

This job can be a hassle, especially if you have painted trim. If you have this clearance and the door still rubs, the door may be warped and/or the entire pocket door assembly may be twisted.

8 Reasons to Consider Sliding Doors Instead Loft kitchen

Adjust the the hangers so the one at the opening sits slightly lower than the other, should only be 13mm spanner and moving two nuts.

How to fix a pocket door that won't stay open. Place it on a hard surface and whack it in the middle with a hammer. Troubleshooting and repairing issues with pocket doors is a simple task most of the time. With the broom handle, slide the roller carriage out into the door opening.

Replacing the track can be a big job that may even require some drywall patching. If you are lucky, the problem may be fixed by simply tightening all the screws in the hinges. You might have to wedge a flathead screwdriver between the head of the pin and top of the hinge.

For a badly warped door, apply wet towels across the warped area only. The new lock should work perfectly. Unscrew the sweep and raise it on the door.

If the door is scraping against the floor, turn the adjustment screw so that it pulls the door upward. Putting the pocket door back on the track Remove the pin by placing a screwdriver under the middle hinge.

Tap some shims under the door to hold it about 1/4″ off the floor. New track and pocket door rollers How to fix a door that won't stay open.

When a door tends to swing slowly open by itself if not latched, you do just the opposite: While the stopper is holding up the door, place the screws back in the track using the screwdriver or drill. Exterior door is hard to open:

If anything is out of place, attach shims to the door frame until you get a level reading. If you have a gap at the bottom of the door that is causing rubbing towards the top of your door, you can lower the door by adjusting the hanger that is. Sometimes, fixing a pocket door problem can be as simple as making a few adjustments with a wrench.

Move them closer to the door until they rub and possibly make some friction so the doors do not move on their own accord. Now tighten all of the hinge screws, on both the door and the door frame. If your exterior door is hard to open, it might be from a loosened threshold piece.

Move the top hinge leaf out (away from the door stop molding) or move the bottom hinge in. Most of the time it is just some adjusting and lubricating. You can try to tighten the threshold screws or replace the threshold and sweep at the same time.

If your closet door or mirror wardrobe door is off the track or won’t stay on, we can repair or replace it for smooth easy operation. Lift the door gently and place magazines under it to support the door. Close the door to have access to the back.

This will widen the gap along the hinge side and narrow the gap along the latch side. A few minutes work and your door will be quiet and smooth. Place that piece of cardboard on the door frame where the hinge will be screwed back into place.

Use a flashlight so that you can see what you are doing. If the door still won't stay open without assistance, remove the screws from the top hinge first. Leave the weight on the door for 24 hours or until the warp is gone.

Use a pocket door wrench to turn the hanger a quarter of a turn at a time until the door is parallel with the jamb. When a door won’t stay open, the casing is probably leaning slightly in the wall frame. Then, close the door and check the keys again.

If you are keeping the original strike plate, make sure the new latch bolt will fit in it properly and that there is no gap between the frame and the plate. A broom handle works well for coaxing the hanger out of the pocket. Pull out a door that’s stuck in the pocket by alternately pulling the top and bottom edges.

For those who take such an activity seriously, it is important to have a watchmaker’s bench and a source of light that casts strong but not harsh light. When the wheels are back on the track, push the door back and place the stopper under the door to hold it up. A flexible lamp of some sort will work well, so that you can bring it closer to the open watch face, or push it a little away if it’s too bright.

Remove the door, sand, and seal it with primer or polyurethane on the top and bottom edges. To readjust the door frame, you have to remove the trim along the latch side to get at the shims. Use a level to ensure that the door frame, and subsequently the track, will be perfectly level once installed.

To stop any banging buy a bit of aluminum angle and use that as a guide and maybe a draught stopper to close the gap. Old pins may need to be pried loose in a different manner. Cut a piece of thin cardboard to the size and shape of the hinge side piece.

For a slightly bowed door, take a heavy weight and lay it across the area that is warped. So try this trick first. If this is the case, it will require major reconstructive surgery to.

Tap the screwdriver with the hammer until the pin pops up from the hinge and can be removed by hand. If your pocket door won’t stay on its track easily, you can do some basic steps to fix this. You can also use glue to do this.

If the door is too high, adjust the screw to lower it. Rather than remove and rehang it, try removing one of the hinge pins. Basically, you are attempting to repair the tension to a workable level.

After the door is taken out and leaned against the wall, you will have to locate the pocket door hanger. Also check to see if the door sweep has lowered. Tightly screw the new lock, in.

One caution, it could rub some of the paint off of the very edge of the door at the very bottom, probably not enough to even notice. After you’ve raised the door and removed the shims, make sure the door hangs at least 3/16″ off the floor. Without closing the door, check the keys to make sure they work.

How to Fix a Car Door Not Closing in Less Than 2 Minutes